Fil Chauffant Toiture

Heating cable in gutters and downspouts: where to install it so that water flows all winter long

In January, a gutter filled with ice overflows, forming long icicles above the entrance. A gutter heating cable installed at the bottom of the gutter and extending all the way to the end of the downspout keeps the meltwater flowing.

Key Points

  • A drainage path, not complete melting: The cable does not melt all the snow on the roof; it keeps a path open from the roof to the ground.
  • One length for the bottom of the gutter; two lengths for gutters that are 5 to 6 inches wide.
  • All the way to the end of the descent: below the frost line if it ends underground; otherwise, with a drainage loop of no more than 1 inch of exposed cable and one end raisedat least 12 inches.
  • Two lengths back and forth down the slope when the current is strong or when the temperature is often below -18 °C.
  • Room thermostat rated for temperatures below 0 °C and installed by an electrician, in accordance with Section 62 of the Quebec Building Code.

Why do gutters and downspouts freeze?

A gutter full of ice, a clogged downspout, an icy driveway: the meltwater has nowhere to go.

Why do Gutters and Downspouts Freeze?

They freeze because meltwater from the roof encounters a cold edge and refreezes there. Installation guides from manufacturers of self-regulating cables describe the phenomenon as follows: snow melts due to the sun or the building’s heat, and the water flows down to the edge of the roof, which remains cold. There, it freezes and forms ice dams and icicles.

The problem doesn’t stop at the eaves. The water that enters the gutter freezes, and the ice then spreads into the downspout—the vertical pipe that carries water from the gutter to the ground. Once this pipe is blocked, any subsequent water has nowhere to go.

The consequences are well known to homeowners in Greater Montreal:

  • A frozen gutter is heavy, which can cause it to warp or break.
  • An overloaded gutter causes water to flow onto the ground, where it refreezes on the driveway.
  • Falling ice cubes pose a risk to people and property.

To better understand how ice forms along the edge of a roof, see our article on roof ice dams.

What a Heating Wire in a Gutter Actually Does

A heating cable does not remove snow from your roof. It creates a continuous drainage path for meltwater, from the roof to the downspout outlet. Snow may remain on the shingles, but the water that melts off them always finds a clear path.

The cable used is a self-regulating cable: its power adjusts automatically based on the ambient temperature. The colder it is, the more heat it generates. When the gutter is dry, it reduces its power. If you want to learn more about how this works, read about how a heating wire works.

Just the Gutter, or the Roof Edge as Well?

Sometimes, the cable in the gutter and downspout is enough. This is the case when no ice dam forms on the eaves—the part of the roof that extends beyond the wall. In this case, water flows freely into the gutter, and the wire simply keeps it from freezing.

If an ice dam forms every winter, we install a zigzag pattern along the edge of the roof. This pattern is connected to the gutter cable so that water trapped behind the ice can drain away. During the inspection, our team identifies where ice forms on your property and then selects the route. Our page on installing Fil Chauffant Toiture details this process.

What About the Valleys and the Roof-to-wall Junctions?

A valley is the depression where two roof slopes meet, and water flows into it. Mark off two-thirds of the valley using two lengths of cable, and the cable should extend into the gutter. If there is no gutter, the cable extends 2 to 3 inches beyond the edge to form a drainage loop—a small loop that allows water to escape without freezing at the edge. The junctions between the roof and a wall are treated according to the same principle: water must always have an outlet.

How the wire is installed in the gutter

A length of cable at the bottom of the gutter, which continues down the downspout.

How the Wire is Installed in the Gutter

In a standard gutter, one length of cable is installed at the bottom. For wide gutters 5 to 6 inches  two lengths are installed. Meltwater flows along the bottom, so that is where the heat is most effective.

Generally, there is no need to secure the cable inside the gutter. It simply rests at the bottom, which also makes spring cleaning easier. The cable then continues on its way through the opening where the gutter empties into the downspout, without being bent.

How the wire is installed in the gutter

The route of the heating cable, from the roof to the outlet at the downspout.

The Downspout the part that Gets Clogged Most Often

When a gutter overflows despite the use of a cable, the cause is often a frozen downspout. The pipe is narrow, and the ice that builds up inside it prevents meltwater from draining off the roof.

For this reason, the cable runs all the way to the end of the descent. There are two possible scenarios:

  • If the drop ends underground, the cable must extend below the frost line—the depth at which the ground no longer freezes in winter.
  • If it ends on the ground, leave a small loop at the bottom, with no more than 1 inch of cable exposed.

The end of the cable—that is, its sealed end cap—must not remain exposed at the bottom of the drop. It must be pulled up at least 12 inches into the pipe, where it is protected.

When the water flow is high, or when temperatures frequently drop below -18 °C (0 °F), a single length is no longer sufficient. In such cases, two lengths are used in the downpipe, arranged in a loop.

Metal or Plastic Gutters: Which Cable?

The same type of cable is suitable for both materials: the self-regulating cable. It reduces its power when the gutter is dry, so it does not overheat plastic gutters or roofing materials. A constant-power cable, on the other hand, heats evenly throughout, which requires greater caution.

In both cases, we follow the manufacturers’ installation guides. You’ll find an overview of the options in our article on types of heating wires.

Thermostat, Circuit, and Code: The Electrical System

A room thermostat controls the system. It measures the air temperature and activates the heating cable when the temperature drops below 0 °C—that is, whenever there is a risk of the water freezing. You don’t have to plug anything in or unplug anything during the winter.

Chapter V, Electricity, of the Quebec Building Code devotes Section 62 to fixed electric heating equipment, which includes heating cables. Section 62-102 requires that these devices be assembled and installed in accordance with the manufacturer’s instructions, as explained in the RBQ’s explanatory notes.

We entrust the connection to the panel to an electrician. The branch circuit—the circuit that supplies power to the cable from the panel—is also subject to safety requirements set forth in the Code. The RBQ has published a technical interpretation on branch circuits (Article 62-114). When choosing between 120 V and 240 V, determine which circuit to install.

Prepare the Gutters Before Installation, in the Fall

October is the right time, because the leaves have fallen and the frost hasn’t yet clogged the downspouts. A cable installed in a gutter clogged with debris cannot keep the water flowing. That’s why our installation begins with a roof inspection and the cleaning of the gutters and downspouts.

Every fall, before winter, here’s what you need to do:

  • Remove leaves and debris from the gutters and downspouts.
  • Check that the control system is working.
  • Have the insulation resistance of the circuits checked; this test confirms that the cable insulation is intact.

Before performing any maintenance on the roof or gutters, turn off the power to the heating cables.

Climb onto the roof with caution—or don’t climb onto it at all. The Régie du bâtiment du Québec reminds the public that snow accumulating along the edges of sloped roofs can be dangerous to passersby. It adds that snow removal and de-icing are arduous and risky tasks, for which it may be prudent to hire a professional.

Frequently Asked Questions About Gutter Heating Cable

No. It keeps a drainage path open for meltwater, from the edge of the roof to the outlet of the downspout. Any remaining snow can melt naturally and drain away through this path.

Generally speaking, no. It is installed at the bottom of the gutter—one section in a standard gutter and two sections in a 5- to 6-inch gutter. We always follow the manufacturer’s instructions for each specific case.

Yes, with a self-regulating cable. It adjusts its power based on the ambient temperature and reduces it when the gutter is dry, so it doesn't overheat the plastic.

All the way to the end. If the run ends underground, it extends below the frost line. If it ends at ground level, leave a small drainage loop, and the end of the cable should extend at least 12 inches back into the pipe.

We do not recommend doing this yourself: the connection must be performed by a licensed electrician, and the installation must comply with the manufacturer’s instructions, in accordance with Article 62-102 of the Code. For an assessment of your roof, gutters, and downspouts, request a free, no-obligation quote.

438-802-7705